The Best Arduino Microphone Amplifier of 2022 – Reviewed and Top Rated

After hours researching and comparing all models on the market, we find out the Best Arduino Microphone Amplifier of 2022. Check our ranking below.

2,084 Reviews Scanned

SaleRank No. #1

10 Pieces Electret Microphone Amplifier Adjustable MAX4466 Module Microphone Preamplifier Blue Breakout Board Compatible with Arduino

Application: the MAX4466 microphone breakout is suitable for voice converters, audio recording and sampling, and audio response projects using FFT; On the back, there is a small trimmer pot to adjust the gain; You can set the gain from 25x to 125x
Parameters: power supply voltage: +2.4V to +5.5V (can be compatible with STM, Raspberry Pi and other development board motherboards); Power supply rejection ratio: 112dB; Common mode rejection ratio: 126dB; AVOL: 125dB (RL = 100 thousands of ohm meter) rail-to-rail output; Quiescent power supply current: less than 24 microamp; Gain bandwidth: 600kHz
20-20KHz electret microphone soldered on: comes with a 20-20KHz electret microphone soldered on the board for audio-reactive projects; It is recommended to use the FFT driver library, which can take audio input and 'translate' it into frequencies
Easy to use: connect GND to ground, VCC to 2.4-5VDC; For the good performance, use the 'quietest' supply available (this would be the 3.3V supply)
Power supply noise rejection function: the amplifier has good power supply noise rejection

Rank No. #2

6 PCS MAX4466 Electret Microphone Amplifier Module Blue Board Breakout Adjustable Gain Compatible with Arduino

Application scenarios: cellular phones, repeating sound device, earphones, hearing aids, microphone preamplifiers, portable computers, voice recognition systems, etc.
This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on.
Easy to use:The board comes with a 20-20KHz electret microphone soldered on Using the MAX4466, an op-amp specifically designed for amplifier; for the best performance, use the "quietest" supply available (on an for Arduino, this would be the 3.3V supply);the amplifier has excellent power supply noise rejection
Parameters: power supply voltage: +2.4V to +5.5V (can be compatible with STM, Raspberry Pi and other development board motherboards); Power supply rejection ratio: 112dB; Common mode rejection ratio: 126dB; AVOL: 125dB (RL = 100kΩ) rail-to-rail output; Quiescent power supply current: <24μA; Gain bandwidth: 600kHz Size:20.8MM*13.8MM*7.5MM
This breakout board is best used for projects such as voice changers, audio recordingmpling, and audio-reactive or DIY projects that use FFT

Rank No. #3

HiLetgo 2pcs Electret Microphone Amplifier MAX4466 Module Adjustable Gain Blue Breakout Board for Arduino

The board comes with a 20-20KHz electret microphone soldered on
Using the MAX4466, an op-amp specifically designed for amplifier
For the best performance, use the "quietest" supply available (on an for Arduino, this would be the 3.3V supply)
The amplifier has excellent power supply noise rejection
This breakout board is best used for projects such as voice changers, audio recordingmpling, and audio-reactive projects that use FFT

Rank No. #4

DIYmalls GY-MAX4466 Electret Microphone Amplifier Sensor Sound Module Adjustable Gain Breakout Board for Arduino (Pack of 2)

MAX4466 microphone breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x.
Add an ear to your project with this well-designed which has excellent power supply noise rejection.
Using is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the "quietest" supply available.
For audio-reactive projects, we suggest using an FFT driver library which can take the audio input and 'translate' it into frequencies.
If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question".

Rank No. #5

DIYmalls LM386 Electret Microphone Audio Amplifier Sound Sensor Module Anti-Reverse Plug with 3pin XH2.54 to Dupont Cable Female for Arduino UNO R3 (Pack of 2)

You can adjust the multiple of magnification of the sound by rotating the potentiometer on microphone sensor. When adjust the potentiometer clockwise to the end, the multiple of magnification is maximum.
The sound sensor comes with a 2.54mm anti-reverse plug-in white terminal. When using it, we can connect to the MCU with DuPont cable. The 4 3mm diameter on-board positioning holes can fix the sensor to other devices.
LM386 Connection with MCU: GND to GND, VCC to 5V, S to AO.
You can buy GY-MAX4466 electret microphone amplifier module via click "Visit the DIYmalls Store"
If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question".

Rank No. #6

ARCELI 2pcs Electret Microphone Amplifier, GY-MAX4466 Breakout Sensor with Adjustable Gain Control for Arduino

1. This breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x.
2. Add an ear to your project with this well-designed which has excellent power supply noise rejection.
3. Using is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply).
4.For audio-reactive projects, we suggest using an FFT driver library which can take the audio input and 'translate' it into frequencies.

Rank No. #7

DAOKI 2PCS Microphone Amplifier Board MAX9814 AGC Microphone Module Auto Gain Control for Arduino with Jump Wire

The MAX9814 is a high-quality microphone amplifier with automatic gain control (AGC) and low-noise microphone bias. The device features a low-noise preamplifier, variable gain amplifier (VGA), output amplifier, microphone-bias-voltage generator and AGC control circuitry.
The low-noise preamplifier has a fixed 12dB gain, while the VGA gain automatically adjusts from 20dB to 0dB, depending on the output voltage and the AGC threshold. The output amplifier offers selectable gains of 8dB, 18dB, and 28dB. With no compression, the cascade of the amplifiers results in an overall gain of 40dB, 50dB, or 60dB.
A trilevel digital input programs the output amplifier gain. An external resistive divider controls the AGC threshold and a single capacitor programs the attack/release times.
A trilevel digital input programs the ratio of attack-to-release time. The hold time of the AGC is fixed at 30ms. The low-noise microphone-bias-voltage generator can bias most electret microphones.
The MAX9814 is available in the space-saving, 14-pin TDFN package. This device is specified over the -40°C to +85°C extended temperature range. MAX9814: Simplified Block Diagram MAX9814: Simplified Block Diagram Enlarge+.

Rank No. #8

Electret Microphone Amplifier MAX4466 with Adjustable Gain for Arduino

Add an ear to your project with this well-designed electret microphone amplifier.
This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on.
This breakout is best used for projects such as voice changers, audio recordingmpling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain.
Using it is simple: connect GND to ground, VCC to 2.4-5VDC.
The output pin is not designed to drive speakers or anything but the smallest in-ear headphones

SaleRank No. #9

Wishiot Electret Microphone Amplifier MAX4466 Sensor Sound Module with Adjustable Gain for Arduino（5）

✧Add an ear to your project with this well-designed which has excellent power supply noise rejection
✧Using is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the "quietest" supply available
✧For audio-reactive projects, we suggest using an FFT driver library which can take the audio input and 'translate' it into frequencies
✧This breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x
✧【 Any questions? / Mass customization?】Please click “Wishiot”(you can find "Sold by Wishiot" under Buy Now button), in the new page, click “Ask a question” to email us

Rank No. #10

Onyehn MAX4466 Electret Microphone Amplifier Module Adjustable Gain for Arduino(Pack of 6pcs)

Power supply voltage:+2.4V to +5.5V
Power supply rejection ratio:112dB:Common mode rejection ratio:126dB
AVOL:125dB(RL = 100KΩ)rail-to-rail output
Static supply current:<24μΑ;Gain bandwidth:600KHz
Size:20.8MM*13.8MM*7.5MM

Last update on 2023-08-13 / Affiliate links / Images from Amazon Product Advertising API

How Do You Buy The Best Arduino Microphone Amplifier?

Do you get stressed out thinking about shopping for a great Arduino Microphone Amplifier? Do doubts keep creeping into your mind? We understand, because we’ve already gone through the whole process of researching Arduino Microphone Amplifier, which is why we have assembled a comprehensive list of the greatest Arduino Microphone Amplifier available in the current market. We’ve also come up with a list of questions that you probably have yourself.

We’ve done the best we can with our thoughts and recommendations, but it’s still crucial that you do thorough research on your own for Arduino Microphone Amplifier that you consider buying. Your questions might include the following:

Is it worth buying an Arduino Microphone Amplifier?
What benefits are there with buying an Arduino Microphone Amplifier?
What factors deserve consideration when shopping for an effective Arduino Microphone Amplifier?
Why is it crucial to invest in any Arduino Microphone Amplifier, much less the best one?
Which Arduino Microphone Amplifier are good in the current market?
Where can you find information like this about Arduino Microphone Amplifier?

We’re convinced that you likely have far more questions than just these regarding Arduino Microphone Amplifier, and the only real way to satisfy your need for knowledge is to get information from as many reputable online sources as you possibly can.

Potential sources can include buying guides for Arduino Microphone Amplifier, rating websites, word-of-mouth testimonials, online forums, and product reviews. Thorough and mindful research is crucial to making sure you get your hands on the best-possible Arduino Microphone Amplifier. Make sure that you are only using trustworthy and credible websites and sources.

We provide an Arduino Microphone Amplifier buying guide, and the information is totally objective and authentic. We employ both AI and big data in proofreading the collected information. How did we create this buying guide? We did it using a custom-created selection of algorithms that lets us manifest a top-10 list of the best available Arduino Microphone Amplifier currently available on the market.

This technology we use to assemble our list depends on a variety of factors, including but not limited to the following:

Brand Value: Every brand of Arduino Microphone Amplifier has a value all its own. Most brands offer some sort of unique selling proposition that’s supposed to bring something different to the table than their competitors.
Features: What bells and whistles matter for an Arduino Microphone Amplifier?
Specifications: How powerful they are can be measured.
Product Value: This simply is how much bang for the buck you get from your Arduino Microphone Amplifier.
Customer Ratings: Number ratings grade Arduino Microphone Amplifier objectively.
Customer Reviews: Closely related to ratings, these paragraphs give you first-hand and detailed information from real-world users about their Arduino Microphone Amplifier.
Product Quality: You don’t always get what you pay for with an Arduino Microphone Amplifier, sometimes less, and sometimes more.
Product Reliability: How sturdy and durable an Arduino Microphone Amplifier is should be an indication of how long it will work out for you.

We always remember that maintaining Arduino Microphone Amplifier information to stay current is a top priority, which is why we are constantly updating our websites. Learn more about us using online sources.

If you think that anything we present here regarding Arduino Microphone Amplifier is irrelevant, incorrect, misleading, or erroneous, then please let us know promptly! We’re here for you all the time. Contact us here. Or You can read more about us to see our vision.

The Best Arduino Microphone Amplifier of 2022 – Reviewed and Top Rated

How Do You Buy The Best Arduino Microphone Amplifier?

Related Post: