The Best Jumbospot of 2022 – Reviewed and Top Rated
After hours researching and comparing all models on the market, we find out the Best Jumbospot of 2022. Check our ranking below.
2,034 (random num) Reviews Scanned
- [What Is It] Small, portable with self contained radio and antenna, SHARI(SA818 Ham Allstar Radio Interface) is designed for construction and uses in the amateur radio service, works with a Pi2/Pi3 or Pi4, SHARI RF output power is 500 to 1000(default) milliwatts
- [Allstar Node] SHARI PiHatU implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz|70cm) radio module; In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired)
- [Power Supply] SA818 Ham Allstar Radio Interface is a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies.
- [Feature 1] Front panel LEDs indicate the status of SHARI-POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red); SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module
- [Feature 2] SHARI PiHat uses a single circuit board which contains installed surface mount (SMD) parts as well as 2 through-hole parts, a surface mount SMA connector and the SA818 (UHF) radio module; PiHatU also uses the Cmedia CM119B USB audio IC.NOTE: Support of SHARI is provided via the SHARI group at www.groups.io/g/shari
- MMDVM hotspot supports D-STAR DMR YSF P25 NXDN POCSAG, enables the different mode of digital two way radio to communicate with each other (YSF2DMR / YSF2NXDN / YSF2P25 / DMR2YSF / DMR2NXDN) and works great in UHF.
- HOTSPOT size: 2.8 x 1.3 x 0.9” inch
- Setup: Set the same freq as Radio Mobile, for example: 433.550000MHZ. DMR WIFI SSID:pi-star,PASSWORD:raspbery. Need the 2.4GHz SSID as the Pi Zero W. doesn't support 5.8GHz
- Power Supply: Mobile charger or a USB cable connected to your computer or laptop..
- Best customer services: fully-assembled. The firmware is pre-loaded. Contact us if any question, we will reply within 6 hours. 73.
- If you have a Zumspot Brand MMDVM Board there is a new case model: ZRPI-3.5NSX
- For Raspberry Pi 4B, 3B+, 3B, 2B, and B+ (not included), JUMBOspot (a generic Chinese MMDVM board - Not included), and a 3.5″ Enhanced Nextion Touchscreen (included). Carefully designed to precisely fit these components using Laser cut components and stainless steel hardware. Full body coverage for components (not waterproof). Heat sinks and rubber feet included.
- Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions.
- Note: This case does not have a fan and the Pi-4 is known to run hot under use. It is not recommended to run the Pi-4 at full power for extended periods as performance problems can arise at higher temperatures.* The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included)
- Engineered and manufactured with Pride in Tacoma, WA USA
- 【Frequency Range】MMDVM hotspot supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)
- 【Applicability】AURSINC hotspot board supports Raspberry Pi 3B, 3B +, Pi Zero W, Pi Zero 2W, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model). if you want a little processor power install on Pi 3 or Pi4, this is a great little hat for digital voice modes.
- 【Multifunction】Hotspot board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG. Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules
- 【Firmware Update】If the Raspberry fails to connect the hotspot board, please try update the firmware of the hotspot board by conducting the command: sudo pistar-mmdvmhshatflash hs_hat. More info pls view: amateurradionotes.com/pi-star-notes.htm#hotspotfwupdate (It can be update the MMDVM firmware version to V1.6.1.)
- 【Compatible with P4 settings】Since our mmdvm board is defautly setup for Pi-Zero W, Pi 3. and if you do want to connect it with your Pi 4, you could try below methods. PICK ONE. Method 1: Remove the R1 resistance of the hotspot board(single/dual) ; Method 2: Cut off the 2 Raspberry Pi pin headers on the corners of the board ( pick one to operate on your MMDVM board, refer to the product image for the R1 and 2 pin headers locations)
- This is case kit. Assembly is required. No components are included.
- Full body coverage for Raspberry Pi, JumboSPOT or LoneStar MMDVM Simplex and OLED screen (not waterproof). Note: Raspberry Pi Zero 2 has not been tested for heat issues. Enough room for .96″ OLED screen to be mounted directly to JumboSPOT or LoneStar MMDVM Simplex by customer
- Cut outs for easy access to SD card and camera ports
- Comes with 2 tops: one with antenna hole and one without
- Pin-hole access to boot and reset buttons on top of case
- [Frequency Range] MMDVM hotspot board is the latest firmware. Supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)
- [Compatible] Hotspot board support Raspberry Pi 3B, 3B +, Pi Zero W, Pi Zero 2W, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USB to TTL or Bluetooth model). If you want a little processor power install on Pi 3 or Pi4, this is a great little hat for digital voice modes.
- [Support MMDVM Mode] MMDVM board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG
- [Features] Support online upgrade, user-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules. It can be update the MMDVM firmware version to V1.6.1
- [Packing list] 1x mmdvm hotspot board(UHF/VHF), 1x antenna, 1x elbow
- Case kit requires assembly. Designed to fit Raspberry Pi 4, 3B+, 3B, 2B, and B+ (not included), and JumboSPOT or N5BOC Lonestar Board. No boards are included.
- Includes a 2.4" Enhanced Nextion Touchscreen. Please note that connecting the Nextion screen to your JumboSPOT or LoneStar may require additional soldering of pins or wires which is not covered in the case instructions.
- The new inner layers have been designed to fit the Pimoroni Fan SHIM (not included). Heatsinks and rubber feet included.
- Designed and Crafted in Tacoma, WA USA
- 【Frequency Range】MMDVM hotspot supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions). If the Raspberry fails to connect the hotspot board, please try update the firmware of the hotspot board by conducting the command: sudo pistar-mmdvmhshatflash hs_hat (Can update the MMDVM firmware version to V1.6.1.)
- 【Applicability】 aursinc mmdvm hotspot board supports Raspberry Pi 3B, 3B +, Pi Zero W, Pi Zero 2W, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model). Great way to roll your own hotspot. Added a Pi Zero 2W, power supply, microSD, and loaded with WPSD. You will have a great simple hotspot. Great way to help learn about DMR
- 【Multifunction】 Hotspot board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG. Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules
- 【Compatible with P4 settings】 since our mmdvm board is defautly setup for Pi-Zero W, Pi 3. and if you do want to connect it with your Pi 4, you could try below methods. PICK ONE. Method 1: Remove the R1 resistance of the hotspot board(single/dual) ; Method 2: Cut off the 2 Raspberry Pi pin headers on the corners of the board ( pick one to operate on your MMDVM board, refer to the product image for the R1 and 2 pin headers locations)
- 【Importance】Receiving and transmitting signals, please refer to this website to test: mmdvm .club/index.php/archives/263/. If you find the unit will transmit but not receive, please kindly contact us. We will help resolve this issue
- Amazon Kindle Edition
- Hall, Allan (Author)
- English (Publication Language)
- 46 Pages - 05/02/2020 (Publication Date)
- Supports PI-STAR's web based digital voice dashboard and configuration tool. Pi-Star Digital Voice Software pre-loaded and easily upgraded via software.
- Supports all four digital amateur modes: DMR, D-Star, P25 and SystemFusion.
- Built-in WiFi: 802.11b/g/n.
- Built-in OLED system status display indicating Mode, TalkGroup and CallSign.
- Built-in LED indicators for status of Power, PTT, COS and Mode.
Last update on 2024-08-11 / Affiliate links / Images from Amazon Product Advertising API
How Do You Buy The Best Jumbospot?
Do you get stressed out thinking about shopping for a great Jumbospot? Do doubts keep creeping into your mind? We understand, because we’ve already gone through the whole process of researching Jumbospot, which is why we have assembled a comprehensive list of the greatest Jumbospot available in the current market. We’ve also come up with a list of questions that you probably have yourself.
We’ve done the best we can with our thoughts and recommendations, but it’s still crucial that you do thorough research on your own for Jumbospot that you consider buying. Your questions might include the following:
- Is it worth buying an Jumbospot?
- What benefits are there with buying an Jumbospot?
- What factors deserve consideration when shopping for an effective Jumbospot?
- Why is it crucial to invest in any Jumbospot, much less the best one?
- Which Jumbospot are good in the current market?
- Where can you find information like this about Jumbospot?
We’re convinced that you likely have far more questions than just these regarding Jumbospot, and the only real way to satisfy your need for knowledge is to get information from as many reputable online sources as you possibly can.
Potential sources can include buying guides for Jumbospot, rating websites, word-of-mouth testimonials, online forums, and product reviews. Thorough and mindful research is crucial to making sure you get your hands on the best-possible Jumbospot. Make sure that you are only using trustworthy and credible websites and sources.
We provide an Jumbospot buying guide, and the information is totally objective and authentic. We employ both AI and big data in proofreading the collected information. How did we create this buying guide? We did it using a custom-created selection of algorithms that lets us manifest a top-10 list of the best available Jumbospot currently available on the market.
This technology we use to assemble our list depends on a variety of factors, including but not limited to the following:
- Brand Value: Every brand of Jumbospot has a value all its own. Most brands offer some sort of unique selling proposition that’s supposed to bring something different to the table than their competitors.
- Features: What bells and whistles matter for an Jumbospot?
- Specifications: How powerful they are can be measured.
- Product Value: This simply is how much bang for the buck you get from your Jumbospot.
- Customer Ratings: Number ratings grade Jumbospot objectively.
- Customer Reviews: Closely related to ratings, these paragraphs give you first-hand and detailed information from real-world users about their Jumbospot.
- Product Quality: You don’t always get what you pay for with an Jumbospot, sometimes less, and sometimes more.
- Product Reliability: How sturdy and durable an Jumbospot is should be an indication of how long it will work out for you.
We always remember that maintaining Jumbospot information to stay current is a top priority, which is why we are constantly updating our websites. Learn more about us using online sources.
If you think that anything we present here regarding Jumbospot is irrelevant, incorrect, misleading, or erroneous, then please let us know promptly! We’re here for you all the time. Contact us here. Or You can read more about us to see our vision.
FAQ:
Q: How much does a jumbospot cost?
A: Low cost. The Jumbospot costs about $45 and I’ve heard tales of people getting them for $35. Slap it on top of a Raspberry Pi Zero W which costs $10 and an SD card and you are on the air for about $70 or so if you factor in everything.
Q: What are the features of the Jumbo spot?
A: Jumbo Spot has a built-in OLED status display that indicates the active mode of operation as well as the call sign and talk group of the current user. The built-in UHF (430-450Mhz) programmable simplex radio allows easy access from your digital handheld or mobile radio.
Q: How does the Jumbo spot RTQ work?
A: The JUMBO SPOT RTQ will select the nearest pre-programmed wireless network automatically. Supports PI-STAR’s web based digital voice dashboard and configuration tool Supports all four digital amateur modes DMR, D-Star, P25 and System Fusion
Q: What is Jumbo spot RTQ mini MMDVM?
A: Jumbo SPOT RTQ Mini MMDVM Jumbo SPOT RTQ is a completely self-contained digital hotspot supporting DMR, Dstar, P25 and System Fusion communications. Fully assembled and tested in a ruggedized aluminum enclosure. All that’s required for operation is a mini usb (android phone ‘s cable)power source and a WiFi based internet connection.