The Best Stabilus Lift O Mat D 56070 of 2023 – Reviewed and Top Rated

After hours researching and comparing all models on the market, we find out the Best Stabilus Lift O Mat D 56070 of 2023. Check our ranking below.

2,276 Reviews Scanned

Rank No. #1

2 Truck Upfitters 16" Gas Props (15.7" Extended, 9.4" Compressed, 45 pounds of Pressure ea) for are, ATC, Snugtop, Leer Camper Shell/Truck Cap Rear Door. Measurement Required! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair of 45 pound (each) gas struts. 15.7" extended length and 9.4" compressed length. This size of door shock absorber is for medium height and weight rear or side camper shell doors. Each canopy shock has 45 lbs of pressure, for a total of 90 lbs of pressure. Please note that this does not mean that it can lift something that is 90 lbs. the typical hinged-style door weight for this prop is approximately 60-80 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all camper shell brands / models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Equivalent to Suspa # c16-23993 or Stabilus #14269. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Rank No. #2

2 Truck Upfitters 17" Gas Props (17.1" Extended, 9.9" Compressed, 45 pounds of Pressure ea) for are, ATC, Snugtop, Leer Camper Shell/Truck Cap Rear Door. Measurement Required! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair of 45 pound (each) gas struts. 17.1" extended length and 9.9" compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 45 lbs of pressure, for a total of 90 lbs of pressure. Please note that this does not mean that these gas lift shocks can lift something that is 90 lbs. the typical hinged-style door weight for this prop is approx 60-80 lbs, including the weight of the camper shell locks & keys.
These gas lift cylinders do not fit all camper shell brands / models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Equivalent to Suspa # C16-04270 or Stabilus # 1822. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Rank No. #3

2 Truck Upfitters 12" Gas Props (12.2" Extended, 8.6" Compressed, 24 lbs of Press ea) for are ATC Snugtop Leer Camper Top Side/Windoors. Measurement REQ'D! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair (2 total) of 24 pound (each) gas struts. 12.2" extended length and 8.6" compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 24 lbs of pressure, for a total of 48 lbs of pressure. Please note that this does not mean that it can lift something that is 48 lbs. the typical hinged-style door weight for this prop is approximately 20-40 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all truck cap/camper shell brands/models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Equivalent to Suspa #C16-03795 or Stabilus #1906. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Rank No. #4

C16-15208 15.7 inch 45Lbs/200N Gas Shocks Struts for are Leer Camper Topper Shell Rear Window, Truck Canopy Cap Cover, Pack of 2PCS.

💠[Most used for] 16" 45lb gas shock struts fit for Leer ARE camper shell topper rear window bed Cover, other custom applications such as cabinet door, outdoor bench lid, toolbox, boat lid, tarp door and so on.
💠[Parameter] Compressed Length (Center-to-Center): 9.4in (239mm). Extended Length (Center-to-Center): 15.7in (399mm). Force: 45 Lbs/200N per Strut. Please measure the length of your original shocks before purchasing.
💠[Tips] Tips for gas spring used on custom applications. If your lid or door weighs 20-40lb, just install ONE. The lid or door weighs 50-85lb, install both. If you are not sure, please contact us before buying, we will provide you with professional advice.
💠[Interchage Number] 025311 14269ARE 5003024510 5159EX 5159EX 5159EX 5159EX C1615208 C16-15208 SE150P45M10
💠[12+1 MONTH REPLACEMENT SERVICE] Welcome to Click "Ask Seller" BESIDE YOUR ORDER for In-time Assistance if any problem occurs.

Rank No. #5

2 Truck Upfitters 16" Gas Props (15.7" Extended, 9.4" Compressed, 38 pounds of Pressure ea) for are, ATC, Snugtop, Leer Camper Shell/Truck Cap Rear Door. Measurement Required! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair of 38 pound (each) gas struts. 15.7" extended length and 9.4" compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 38 lbs of pressure, for a total of 76 lbs of pressure. Please note that this does not mean that it can lift something that is 76 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all truck cap/camper shell brands/models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Equivalent to Suspa # c16-09209 or Stabilus # 01824. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Rank No. #6

2 Pcs Gas Struts 15.7 Inch 45 lbs Prop Shock Lift Springs Rod for Truck Canopy Cap Cover ARE Leer Camper Topper Shell Rear Window C1615208 C1622331

Specification--Extended Length (Center-to-Center): 15.7 in , Force: 45 Pounds Per Strut, Suitable support weight is from 35 pounds to 50 pounds.
Application--Suitable to use on toolbox lid door, outdoor TV cabinet, shed window, trap or floor hatch door, truck cover camper window shell.
Interchange Part Number-- OEM Numbers C16-15208 C16-22331 C1615208 C1622331
Installation--The package contains 2 pillars, 4 ball mounting bracket and nut. Do not try to compress by hand, otherwise the pillars will be damaged.
Our Commitment-- If you unluckily encounter with missing parts or unfit problem, just click "Ask Seller" for immediate assistance!

Rank No. #7

2 Truck Upfitters 16" Gas Props (15.7" ext, 9.4" Compressed, 55 lbs of Pressure ea) Compatible with are, ATC, Snugtop, Leer Campers. Measurement REQ'D! Incl 4 Ball mounts+Angled & Straight Fittings!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL TOPS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair of 55 pound (each) gas struts. 15.7" extended length and 9.4" compressed length. This size of door shock absorber is for tall medium/heavy weight rear or side camper shell doors. Each canopy shock has 55 lbs of pressure, for a total of 110 lbs of pressure. Please note that this does not mean that it can lift something that is 110 lbs. the typical hinged-style door weight for this prop is approximately 70-90 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all camper shell brands / models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Compatible with Suspa # c16-23994 & compatible with Stabilus # 025657 These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Rank No. #8

C1606389 14 inch Gas Struts, 107N/24Lbs Gas Shocks Spring Lift-o-mat Truck Camper Shell Lift Supports for Leer Topper Truck Cap, Camper Shell, Canopy Window Lift, Tool Box (2 Pack)

Rank No. #9

2 Truck Upfitters 12" Gas Props (12.2" ext, 7.5" comp, 40 lbs ea) for are Snugtop Leer Camper Doors & ONLY Aluminum Weatherguard ONLY Toolboxes. Measurement REQ'D! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair (2 total) of 40 pound (each) gas struts. 12.2" extended length and 7.5" compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 40 lbs of pressure, for a total of 80 lbs of pressure. Please note that this does not mean that it can lift something that is 80 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all camper shell brands / models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Equivalent to Suspa #C16-11028, Stabilus #19068, or Weatherguard 7009-2PK . Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors & awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, other toolbox struts, etc. These gas shock lift supports CAN'T be compressed by hand. They MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position.
NOT FOR STEEL TOOLBOXES- WILL NOT HOLD UP LID. Fit most Weatherguard ALUMINUM truck bed toolboxes ONLY, models 121-0-01, 121-5-01, 123-0-01, 123-5-01, 127-0-01, 127-5-01, 131-0-01, 131-5-01, 137-0-01, 137-5-01, 147-0-01, 147-5-01, 154-0-01, 154-5-01. Compatible with many truck canopy types, including LEER, ARE, Century, Snugtop, and ATC tops, & many other brands that utilize gas shocks / gas springs / gas lifts. Compatible with many gas lift brands, including stabilus, lift o mat, & Suspa.

Rank No. #10

C16-04145 15 inch 24Lbs/107N Gas Shocks Struts for are Leer Snugtop Camper Topper Shell Rear Window, Truck Canopy Cap Cover, Cabinets Door, Set of 2 Vepagoo.

🍎【Most used for】C16-04154 14.45 inch 24Lbs/107N gas shock strut compatible with 14''-15''/19lb-26.5lbLeer ARE SnugTop camper shell truck topper rear window, Truck Pickup Cab Canopy Door, Cabinets Door and other custom Applications.
🍎【Parameter】Compressed Length (Center-to-Center):14.45"(367mm), Extended Length (Center-to-Center): 8.98" (228mm), Force: 24 Lbs Per Strut, two are 48LB.
🍎【Note】Please compare the length of your original gas spring' compression and extension, type of connector, and lift capability before purchasing.
🍎【INTERCHANGE NUMBER】C16-04145 C16-04145. Easy to install, no special tools required. End Fitting: 10mm Sockets.
🍎【12+1 MONTH REPLACEMENT SERVICE】Welcome to Click "Ask Seller" BESIDE YOUR ORDER for In-time Assistance if any problem occurs.

Rank No. #11

C1608055 19.7 inch 120Lbs Shock Struts for are Leer Truck Bed Tonneau Cover RV Bed Lift Camper Shell, Shed Window Floor Hatch Door, and Other DIY Applications, Set of 2 Vepagoo.

[APPLICATION] 20in 120lb per gas shock compatible with queen bed oversize mattress, ARE Leer truck pickup bed tonneau Cover, camper bed, travel trailer bed, murphy bed, shed window, and other heavy-duty DIY appliacation.
[PARAMETER] Interchange Part Number C16-08055 C1608055. Extended Length:19.69", compressed Length: 12.20"; End Fittings:10mm Nylon Ball Sockets. Mounting bracket needed (Not INCLUDED ): 10mm Ball Stud Mounting Bracket.
[NEED KNOW] If you used these gas shocks as a replacement for the Truck Tonneau Cover or Trailer cover, you have to compare the length of your original gas spring' compression and extension, type of connector, and lift capability before purchasing.
[TIPS] 120lb Per strut, two are 240lb. Super strong!! You couldn’t compress it by your hand! Suitable for lids or doors weighing between 100b and 150lb. Don't buy for a lightweight project less than 80LB. If you think these 120lb gas shocks are too STRONG or too HEAVY for your PROJECT, please contact us for a more suitable one.
[12+1 MONTH REPLACEMENT SERVICE] Welcome to Click "Ask Seller" BESIDE YOUR ORDER for In-time Assistance if any problem occurs.

Rank No. #12

C16-23994 16 inch 55 lbs Gas Strut, 15.7" Gas Spring Shock Prop Lift for Camper Shell Leer A.R.E Topper Rear Window Side Window Pickup Truck Cab Canopy Door, 2 Pack by PAMAGOO

[16 Inch Gas Spring Specifications] 🚙 Extended length: 15.67 Inch, Compressed length: 9.37 Inch. 55 Lb / 245 N per strut, 2 PACK. Package information: 16 inch 55 lbs gas prop strut X 2;
[16 Inch Gas Strut Replaceable Part Number] 🚙 This 1 pair of PAMAGOO lift struts could perfectly replace the worn-out shocks, interchange number: 1643ED, 515060, 5669BW, 5UGF841500, 5UG-F8415-00, 5UGF841501, 5UG-F8415-01, 7745SR, 7787QS, 8195517, C1615066, C16-15066, C1623994, C16-23994, CS150060, CS1500-60, GP515060, GS515060, ML1360, ML13-60, ML-13-60, ML3360, ML33-60, ML-33-60, SE150P60.
[Scope of Application for Gas Springs] 🚙 Perfect OEM Replacement 16 inch gas sturt shock for C16-23994: Precisely designed according to the original gas shock, prop shock can be used in your Camper Shell Door Glass Window Hatch Strut/Pickup Canopy Leer Truck Rear Hatch Door Cover Glass Aluminum Hatch/ Aft Floor Locker Door/Hot Tub Cover/Hatchback Glass Door/Motorehome's Compartment Door/RV Bottom Door/Spa Cover Lift/Tool Box.
[Easy-to-Install Gas Struts] 🚙 Our gas springs are designed for easy installation, with simple mounting and adjustment. Just use a small screwdriver to pry off the metal clip of the old strut, remove it, and then align the new strut with the original end fitting. Press it into place with your fingers, and the installation is complete! Our customer service team is also available to provide guidance and support during installation.
[Our Commitment to Gas Shocks] 🚙 Every PAMAGOO gas strut has undergone 180,000 durability tests to ensure its service life and smooth operating performance. PAMAGOO will provide 18-months of replacement support to ensure your peace of mind!

Rank No. #13

Lift Supports Depot Qty 2 Replaces Solera 654150 Lift-O-Mat 778N 175lb Awning 26.50" PM3888

This listing includes 2 automotive Lift Supports For the Universal.
Extended Length from Center Mount to Center Mount is 26.5 in.
Lift Supports Depot supports are High Quality Lift Struts. Designed to install easily in minutes, often times without special tools.
These automotive autoparts installs easy with no special tools required.
Compatible with the following OEM Numbers: PM3888

Rank No. #14

PAMAGOO 15 inch 40 lbs Gas Shock C16-21702, 15" Gas Prop Spring Strut Lift for Leer Snugtop Camper Shell Rear Topper Window Pickup Cab Canopy Door Cabinets Door Toolbox Lid, 2 Pack

🚙15 inch gas spring parameters🚙Extended Length: 14.96 inch; Compressed Length: 9.45 inch. 40 lbs per prop. 2 PACK!!!
🚙INTERCHANGE NUMBER🚙 This 1 pair of Pamagoo lift struts could perfectly replace the worn-out shocks,Interchange number: C16-21702, C1621702.
🚙Scope of application🚙 Perfect OEM Replacement 15 inch gas sturt shock for C16-21702: Precisely designed according to the original gas shock, prop shock can be used in your Camper Shell Door Glass Window Hatch Strut/Pickup Canopy Leer Truck Rear Hatch Door Cover Glass Aluminum Hatch/Hot Tub Cover/Hatchback Glass Door/Motorehome's Compartment Door/RV Bottom Door/Spa Cover Lift/Tool Box.
🚙Easy to install lift support struts🚙 We have gas spring installation videos and online service to guide quick installation in minutes, just use a small screwdriver to pry up the metal clip of the old strut to remove it, and then align the new strut onto the end fitting of your car, press with your finger to snap it into place, done!
🚙Our promise🚙 every Pamagoo gas struts has been undertaken with 180,000 times durability test to ensure its service life and smooth working performance, Pamagoo will provide 18 months replacement support to ensure your no-worries using!

Rank No. #15

ARANA C16-04445 17 inch 55 lb Gas Struts Shock Spring 4514 17" Lift Supports 55 Lbs/245 N Gas Prop(17.2" extended) for Leer Camper Shell A.R.E Truck Canopy Topper Window Toolbox Lid Cap Top Door, 2Pcs

✅ Interchange Number: 4514, 4514S10, C1604445, C16-04445,1595EY,8195565, AH8650, ML1650, ML16-50, ML-16-50, ML3650, ML36-50, ML-36-50, P2032, SE172P55,SE618A45PS130PM3, SE630V-55, SL1650, SL16-50, SL-1650, SL-16-50, SL16501, SL16-50-1, SL-16501,SL-16-50-1, SL16505, SL16-50-5, SL-16505, SL-16-50-5, SL3650, SL36-50, SL-3650;
✅ 17 inch 55Lb Gas Struts -- Extended Length (Center-to-Center): 17.2" (436.9 mm); Compressed Length (Center-to-Center): 10.6" (269mm); Force: 55 lbs (245N) Per Strut, 2 Struts per set, not 1;
✅ 4514 17 inch Gas Spring -- ARANA 4514 struts could be used as the replacement parts for toolbox lid, truck topper, Leer cap, camper shell, truck canopy top, etc.
✅ 17 inch 55lb Gas Shocks C16-04445 -- Please confirm the Interchange Number of your old struts if you use the struts as the replacement, and re-check the length before purchasing to avoid buy wrongly;
✅ 18 Months Support-- If any questions or dissatisfaction before/after purchasing or need installing/using guide, please message ARANA directly to let us provide in-time assistance to you!

Rank No. #16

2 Truck Upfitters 13" Gas Props (13" Extended, 8.1" Compressed, 30 pounds of Pressure ea) for A.R.E, ATC, Snugtop, Leer Camper Shell/Truck Cap Rear Door. Measurement Required! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL TOPS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure camper struts from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair of 30 pound (each) gas struts. 13.0" extended length & 8.1" compressed length. This size of door shock absorber is for tall medium weight rear or side camper windows / camper shell doors. Each canopy shock has 30 lbs of pressure, for a total of 60 lbs of pressure. Please note that this does not mean that it can lift something that is 60 lbs. the typical hinged-style door weight for this prop is approximately 30-50 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all camper shell brands / models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Equivalent to Suspa # c16-04464 or c16-04464A or Stabilus # 0516. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect for your topper!

SaleRank No. #17

C1608054 20" Gas Prop Spring Strut 20 inch 100 Lb Per Shock C16-08054 for Camper Shell RV Bed Tonneau Cover Storage Box Basement Door Floor Hatch Window Lift Struts (Applicable Lid Weight 85-110LBs)

✅ ARANA 20 inch Gas Struts C1608054 Lift Supports -- 2Pcs Set Force 100 Pounds 445N Gas Shocks , most SUITABLE support weight for 2 STRUTS is 85 lbs - 110 lbs, this means if your project lid is between 85 pounds and 110 pounds, this 100LB gas strut set is SUITABLE!
✅ ARANA 20 Inch 100 Lbs Gas Spring Shocks -- Extended Length A [in]: 19.7(500mm), Compressed Length B [in]: 11.8(300mm), Interchange number: 6939, 6939S10, C1608054, C16-08054; measurement of the supported lid weight or of your old strut pressure is required to prevent purchasing wrongly!
✅ C16-08054 Gas Props 20inch -- Direct replacement struts for RV bed, motorhome bed, tanning bed, camper bed, travel trailer bed mattress, queen bed, etc.;Note: DO NOT compress them by hands before installing, the struts could only be compressed after installing successfully!!!
✅ ARANA C1608054 100 lb Lift Supports -- Customer will also use them on tonneau cover, heavy camper shell roof, tv cabinet door, trailer window, compartment door, floor hatch, truck cover, bar shed window, heavy custom build lid, etc; Very Strong, do not buy them for the lid weight less than 80 pounds;
✅100% Satisfaction Service -- 18 Months Support comes with every ARANA product; If any questions before purchasing or dissatisfactions after purchasing or need installing/using guide, welcome to click "ASK SELLER" besides your order from ARANA for immediate assistance!

Rank No. #18

BOXI 2pcs Universal Lift Supports Struts Shocks Gas Struts Shocks Springs Supports Extended Length 10 inches/Compressed Length 6.75 inches / 60lbs Force / 10.2mm Eyelet Hole Ends | SG459003 4037

Extended Length: 10.00 inches (measured between the ball fitting centre)
Compressed Length: 6.75 inches (measured between the ball fitting centre)
Each Strut Force (lbs) 60.00, ext.ser.num 267 N
End Fitting: Eyelet Hole=10.2mm=13/32"=.402"
5-Year Limited Warranty

Rank No. #19

2 Truck Upfitters 16" Gas Props (15.7" Extended, 9.4" Compressed, 28 lbs of Press ea) Compatible with are, ATC, Snugtop, Leer Camper Shell/Truck Cap Rear Door. Measurement REQ'D! Incl 4 Ball mounts!

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS! THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT! SEE PICTURE! Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head (little plastic end), to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5% size variation.
Truck Upfitters Pair of 28 pound (each) gas struts. 15.7" extended length and 9.4" compressed length. This size of door shock absorber is for short & light weight rear or side camper shell doors. Each canopy shock has 28 lbs of pressure, for a total of 56 lbs of pressure. Please note that this does not mean that it can lift something that is 56 lbs. the typical hinged-style door weight for this prop is approximately 30-40 lbs, including the weight of the camper shell locks and keys.
These gas lift cylinders do not fit all truck cap/camper shell brands/models. Measure your strut from center of socket to center of socket when fully opened & fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.
Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper / canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED / OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.
Equivalent to Suspa # c16-09841 These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks / gas springs / gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper!

Rank No. #20

Lift-O-Mat Gas Springs Silver, Pair

Effortless opening of doors and lids. Softer and quieter closing. Smooth motion and stopping.
Secure holding in open and closed positions. Easy to mount/install. Maintenance free.
Compact and attractive design. Opens to 90 Degrees. One pair does one door.
Maximum door height 24"

Last update on 2023-09-04 / Affiliate links / Product Titles, Images, Descriptions from Amazon Product Advertising API

How Do You Buy The Best Stabilus Lift O Mat D 56070?

Do you get stressed out thinking about shopping for a great Stabilus Lift O Mat D 56070? Do doubts keep creeping into your mind? We understand, because we’ve already gone through the whole process of researching Stabilus Lift O Mat D 56070, which is why we have assembled a comprehensive list of the greatest Stabilus Lift O Mat D 56070 available in the current market. We’ve also come up with a list of questions that you probably have yourself.

We’ve done the best we can with our thoughts and recommendations, but it’s still crucial that you do thorough research on your own for Stabilus Lift O Mat D 56070 that you consider buying. Your questions might include the following:

Is it worth buying an Stabilus Lift O Mat D 56070?
What benefits are there with buying an Stabilus Lift O Mat D 56070?
What factors deserve consideration when shopping for an effective Stabilus Lift O Mat D 56070?
Why is it crucial to invest in any Stabilus Lift O Mat D 56070, much less the best one?
Which Stabilus Lift O Mat D 56070 are good in the current market?
Where can you find information like this about Stabilus Lift O Mat D 56070?

We’re convinced that you likely have far more questions than just these regarding Stabilus Lift O Mat D 56070, and the only real way to satisfy your need for knowledge is to get information from as many reputable online sources as you possibly can.

Potential sources can include buying guides for Stabilus Lift O Mat D 56070, rating websites, word-of-mouth testimonials, online forums, and product reviews. Thorough and mindful research is crucial to making sure you get your hands on the best-possible Stabilus Lift O Mat D 56070. Make sure that you are only using trustworthy and credible websites and sources.

We provide an Stabilus Lift O Mat D 56070 buying guide, and the information is totally objective and authentic. We employ both AI and big data in proofreading the collected information. How did we create this buying guide? We did it using a custom-created selection of algorithms that lets us manifest a top-10 list of the best available Stabilus Lift O Mat D 56070 currently available on the market.

This technology we use to assemble our list depends on a variety of factors, including but not limited to the following:

Brand Value: Every brand of Stabilus Lift O Mat D 56070 has a value all its own. Most brands offer some sort of unique selling proposition that’s supposed to bring something different to the table than their competitors.
Features: What bells and whistles matter for an Stabilus Lift O Mat D 56070?
Specifications: How powerful they are can be measured.
Product Value: This simply is how much bang for the buck you get from your Stabilus Lift O Mat D 56070.
Customer Ratings: Number ratings grade Stabilus Lift O Mat D 56070 objectively.
Customer Reviews: Closely related to ratings, these paragraphs give you first-hand and detailed information from real-world users about their Stabilus Lift O Mat D 56070.
Product Quality: You don’t always get what you pay for with an Stabilus Lift O Mat D 56070, sometimes less, and sometimes more.
Product Reliability: How sturdy and durable an Stabilus Lift O Mat D 56070 is should be an indication of how long it will work out for you.

We always remember that maintaining Stabilus Lift O Mat D 56070 information to stay current is a top priority, which is why we are constantly updating our websites. Learn more about us using online sources.

If you think that anything we present here regarding Stabilus Lift O Mat D 56070 is irrelevant, incorrect, misleading, or erroneous, then please let us know promptly! We’re here for you all the time. Contact us here. Or You can read more about us to see our vision.

The Best Stabilus Lift O Mat D 56070 of 2023 – Reviewed and Top Rated

How Do You Buy The Best Stabilus Lift O Mat D 56070?

Related Post: