Contents

The Best Atx Breakout Board of 2023 – Reviewed and Top Rated

After hours researching and comparing all models on the market, we find out the Best Atx Breakout Board of 2023. Check our ranking below.

2,422 Reviews Scanned

Rank No. #1

Electronics-Salon 24/20-pin ATX DC Power Supply Breakout Board Module.

Electronics-Salon 24/20-pins ATX DC Power Supply Breakout Board.
24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header.
Stand-By and Power-ON indicator LEDs.
With latching button switch to control power ON/OFF.
High quality 24Amp(per position) screw terminal blocks.

Rank No. #2

HLT New Version ATX Power Supply Breakout Board and Acrylic Case Kit with ADJ Adjustable Voltage Knob, Supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) Output Voltage, 3A Maximum Output, Reset Protection.

1.ATX power supply breakout board, with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) output voltage.
2.The voltage output terminals of the ATX power expansion board correspond to each screw terminal.
3. At the same time, the panel is also equipped with an acrylic case kit for easy to use.
4.Compatible with 3.3V: STM32 MCU, network communication equipment, such as Wi-Fi Bluetooth and other devices, generally for microcontrollers, and some low-power modules, etc. 5V: Raspberry Pi, Banana Pi, Tinker Board, Nano Pi, USB interface, etc.
5.Compatible with 9V: Arduino, motor drive, display driver module, etc. 12V: motor drive, LED light, vehicle equipment with power requirements less than 24w, etc.

Rank No. #3

Songhe XH-M229 24 Pins Benchtop Power Board Computer ATX Power Supply Breakout Adapter Module Desktop Computer Chassis Power Supply ATX Transfer to Adapte Board 3.3V 5V 12V 1pcs

4 sets of typical output voltages: 3.3V, 5V, 12V and -12V.
The board should be powered by a standard computer power supply with an ATX connector.

Rank No. #4

MELIFE 2pcs 24 Pin ATX Power Supply Breakout Adapter Module Desktop Computer Chassis Computer PC Power Supply Breakout Module Adapter 12V 5V 3.3V ATX Transfer Board

OPTIMAL PERFORMANCE: Premium upgrade XH-M229 ATX Power Transfer Board can output our different voltages groups, PCB plastic gasket design to prevent short circuit.
HIGH QUALITY: Premium XH-M229 ATX Power Transfer Board is made of high quality material which can use for a long time.
COMPATIBILITY: XH-M229 Power Transfer Board is compatible with the port: ATX (partial BTX type). Each output channel has replaceable 5A fuse and corresponding grounding connection, and the terminals are easy to connect.
OPTIMAL RELIABILITY: On board standard 24 pin ATX port, power indicator and power switch are ideal for easy control of DIY low voltage power supply for developing physical computing projects (embedded systems).
EASY to USE: Designed to use your power supply to create a desktop power supply with four-channel voltages that can run almost any embedded electronic project.

Rank No. #5

PSU Breakout Board ATX Power Supply DC 12V 5V 3.3V Splitter Module Desktop Adapter to USB A Hub Connector Computer Power Source Multi Port Output DIY Parent Child Electronic Kit with High Current Fuse

【24pin 20pin】Compatible with 24-pin and 20-pin ATX mains. When inserting 20 pin, please align to the right. Different PSU may provide different maximum currents.
【Fuse】Yaotech Advanced Technology Extended conversion connector is equipped with 5A and 8A high amp fuses for your choice, one more protection is safer and necessary. Electronic enthusiasts can modify it with soldering tools too.
【Ports】This PC power supply unit Hub has direct current 12V*3, 5V*2, 3.3V*1, -12V*1, USB-A 5V*2 voltage output ports. It can be used for high amperage led desk lamp, smart phone charging, just normal charging, fast charging is not supported, electric toy charging, student handmade items for school, electronic learning & education project, etc.
【Indicator Lights】This PSU converter has independent switch and 4 blue indicator lights to indicate 4 voltage output ports. When the fuse is blown, the corresponding indicator light will go out.
【Feet】We provide 4 insulated feet, when you need to put the pcb board on the metal table, you can install insulated feet to avoid short circuit.

Rank No. #6

AITRIP XH-M229 Desktop Computer Chassis Power Supply ATX Transfer Board Power Take Off Board Power Output Terminal Module 24Pin (3PCS)

Each output channel has replaceable 5A fuse and corresponding ground connection with binding post easy to connect
Provide quick access to the typical voltages needed including 3.3V, 5V, 12V and -12V.
Compatible with the port: ATX (compatible with partial BTX type)
The PIN number: 24 pin ; power indicator and power switch easy to control ideal to DIY low voltage power supply for developing physical computing projects (embedded systems)
Feature: 1. With power output indicator. 2. With module switch to turn off output 3.The output terminal can pass the maximum current. 4. With output protection fuse,four groups correspond to four road output.

Rank No. #7

risingsaplings ATX DC Power Supply Breakout Board 24/20-pin

Type: 24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header.
LED design: Stand-By and Power-ON indicator LEDs.
Switch design: With latching button switch to control power ON/OFF.
High quality screw terminal blocks for fast connections.
Package list: 24-pins Standard ATX Connector x 1 pcs

Rank No. #8

Hyhpsjiee 3pcs 24 Pin ATX Power Supply Breakout Adapter Module Desktop Computer Chassis Computer PC Power Supply Breakout Module Adapter 12V 5V 3.3V ATX Transfer Board.

With power output indicator.With module switch to turn off output.
With output protection fuse,four groups correspond to four road output.
This port is used together On-board standard 24pin ATX port, power indicator and power switch easy to control ideal.
Each output channel has replaceable 20A glass fuse and corresponding ground binding posts for easy connection.
Please note that if the power supply is a 20PIN port other than a 24PIN port, the socket is inserted from the dot mark on the circuit board.-12V cannot be loaded, it is only provided by the motherboard

Rank No. #9

24,20 Pin ATX DC Power Supply Board Module, PC Power Adapter Board, Computer Power Supply Adapter Module Compatible with 20,20 4,24 Pin Headers

Rank No. #10

20/24 Pins ATX Benchtop PC Power Breakout Adapter with USB 5V Port 24pin Right Angle ATX 24 pin ATX case pc Power Supply (Green)

Designed to take advantage of your power supply to create a benchtop power supply with 4 channel voltages to run almost any of your embedded electronics projects
Provide quick access to the typical voltages needed including 3.3V, 5V, 12V and -12V
Each output channel has replaceable 5A fuse and corresponding ground connection with binding post easy to connect
On-board standard 24pin ATX port, power indicator and power switch easy to control ideal to DIY low voltage power supply for developing physical computing projects (embedded systems)
PCB plastic spacer design for preventing short circuit .

Rank No. #11

CHENBO 2pcs 24 Pins ATX Power Board Computer PC Power Supply Breakout Module Adapter 12V 5V 3.3V

✿Designed to use your power supply to create a desktop power supply with four-channel voltages that can run almost any embedded electronic project.
✿Fast access to the typical voltage required, including 3.3V, 5V, 12V and -12V
✿Each output channel has replaceable 5A fuse and corresponding grounding connection, and the terminals are easy to connect.
✿On board standard 24 pin ATX port, power indicator and power switch are ideal for easy control of DIY low voltage power supply for developing physical computing projects (embedded systems).
✿PCB plastic gasket design to prevent short circuit.

Rank No. #12

GeeekPi 24/20-pin ATX DC Power Supply Breakout Board Module Adapter, Terminal Block Breakout Module for Computer PC

24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header.
Support ATX/STX power supply
With latching button switch to control power ON/OFF.
Each channel has independent indicator LEDs
One-time lock button design

Rank No. #13

New Version ATX Power Supply Breakout Board and Acrylic Case Kit with ADJ Adjustable Voltage Knob, Supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) Output Voltage, 3A Maximum Output, Reset Protection.

1.ATX power supply breakout board, with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) output voltage.
2.The voltage output terminals of the ATX power expansion board correspond to each screw terminal.
3. At the same time, the panel is also equipped with an acrylic case kit for easy to use.
4.Compatible with 3.3V: STM32 MCU, network communication equipment, such as Wi-Fi Bluetooth and other devices, generally for microcontrollers, and some low-power modules, etc. 5V: Raspberry Pi, Banana Pi, Tinker Board, Nano Pi, USB interface, etc.
5.Compatible with 9V: Arduino, motor drive, display driver module, etc. 12V: motor drive, LED light, vehicle equipment with power requirements less than 24w, etc.

Rank No. #14

WWZMDiB XH-M229 24 Pin Benchtop Computer Power Board/Computer Chassis Power Supply Breakout Adapter ATX Transfer Board 3.3V 5V 12V

💎XH-M229 24 Pin Supply Breakout Adapter
⚡4 groups of typical output voltages: 3.3V, 5V, 12V and -12V.
🥇The board should be powered by a standard computer power supply with an ATX connector.
🥈Size: 12.8x4.8cm/5.04x1.89"
🥉If your power supply is a 20pin port or a port other than 24pin, plug the socket from the dot mark on the circuit board, pay attention when using it.

Rank No. #15

OONO ATX 24/20-Pin DC Power Supply Breakout Module with 2.1A USB Port

24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header.
Stand-By and Power-ON indicator LEDs. With latching button switch to control power output ON/OFF, it also supports external latching switch control power output ON/OFF(when using an external switch, the switch state on the module must be set to OFF)
With USB 5V power output, can support 2.1Amp output current for Apple products.
High quality screw terminal block for power output. +3.3V +5V +12V can support current maximum 24 Amp(continuous output 12 Amp), -12V can support current maximum 1 Amp.
ABS plastic enclosure, you can use screw mount to wood board or wall, of course, can also be placed on the desktop.

Rank No. #16

24/20-Pin ATX DC Power Supply Diagnostic/Breakout Board Module

24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header. With latching button switch to control ATX power supply output ON/OFF.
Total 16 LEDs, it is convenient for you to diagnose the functions of all pins except COM/GND, therefore, if the output of any one wire of your ATX power supply is faulty, it can be seen at a glance.
High quality screw terminal blocks. Each terminal position support current output maximum 10 Amp. Pitch 5.0mm/0.197 inch, Wire range 26AWG to 12AWG / 2.5mm square.
Packing list: 1x Diagnostic breakout board, 4x Screws, 4x Nylon spacers.
Special Note: The PS_ON LED lights up when the output is OFF and goes out when the output is ON, this is just the opposite of the indication status of other LEDs. Since many new ATX power supplies no longer provide output -5V, the NC/-V LED will not light up when connected to this type ATX power supply.

Rank No. #17

Goshyda ATX Power Supply Board, for STM32 MCU, Network Communication Equipment

▶【ATX power splitter board】 with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V‑10.8V (ADJ) output voltage.
▶【voltage output terminal 】The voltage output terminal of the ATX power expansion board corresponds to each screw terminal.
▶【easy to use】At the same time, the panel is also equipped with an acrylic box kit for easy use.
▶【Compatible with 3.3V】: STM32 MCU, network communication equipment, such as Wi‑Fi for Bluetooth and other devices, generally for microcontrollers, and some low‑power modules, etc. 5V
▶【Compatible with 9V motor drive】 display drive module, etc.; 12V motor drive, LED lights, vehicle equipment requiring less than 24w of power, etc.

Rank No. #18

ATX Power Supply Board and Acrylic Case Kit, ATX Power Supply Adapter for MCU Electronic Component Adjustable Voltage Knob 24Pin

[ATX power splitter board] ATX power splitter board, with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) output voltage
[Precise Screw Positioning] The voltage output terminal of the ATX power expansion board corresponds to each screw terminal
[With an acrylic box] At the same time, the panel is also equipped with an acrylic box kit for easy use
[Easy to Connect] Compatible with 3.3V: STM32 MCU, network communication equipment, such as Wi-Fi for Bluetooth and other devices, generally for microcontrollers, and some low-power modules, etc. 5V: for Raspberry Pi/Tinker Board/Nano Pi/USB interface, etc
[Widely Compatible] Compatible with 9V motor drive, display drive module, etc.; 12V motor drive, LED lights, vehicle equipment requiring less than 24w of power, etc

Rank No. #19

Cablecc 1200W Server PSU Power Supply Breakout Board Adapter with 17 Ports ATX 6 Pin for DPS-800GB 1200FB 1200QB

Maximum support 1200W . Ounce Copper PCB, solid capacitor filter, 17 of 2 x 3 Pin ATX output.
Suitable for a variety of server bare board accessories, you can also choose adding 17pcs output wires.
The LED voltage display can display the voltage of the main PSU in real time.
Output : 12V , Application for Graphics Card
This adapter is suitable for the following models of : DPS-800GB A . DPS-1200FB A. DPS-1200QB A. PS-2751-5Q . PS-2751-LF-1F. HSTSN-PL12. DPS-700LB D. PS-2112-5L. DPS-750RB A.

Rank No. #20

ALMOCN 2PCS 24 Pin XH-M229 Benchtop Power Board Computer ATX Power Supply Breakout Adapter Module Desktop Computer Chassis Power Supply ATX Transfer Board 12V 5V 3.3V

4 Output Voltages: Providing quick access to 4 sets of typical output voltages, which including: 3.3V, 5V, 12V and -12V.
Each output channel has replaceable 5A fuse and corresponding ground connection with binding post easy to connect.
With power light and power switch.
24 Pin: Standard 24pin ATX port.
Usage:The benchtop power board kit was created to provide quick access to the typical voltages needed when developing physical computing projects (embedded systems).

Last update on 2023-08-07 / Affiliate links / Product Titles, Images, Descriptions from Amazon Product Advertising API

How Do You Buy The Best Atx Breakout Board?

Do you get stressed out thinking about shopping for a great Atx Breakout Board? Do doubts keep creeping into your mind? We understand, because we’ve already gone through the whole process of researching Atx Breakout Board, which is why we have assembled a comprehensive list of the greatest Atx Breakout Board available in the current market. We’ve also come up with a list of questions that you probably have yourself.

We’ve done the best we can with our thoughts and recommendations, but it’s still crucial that you do thorough research on your own for Atx Breakout Board that you consider buying. Your questions might include the following:

Is it worth buying an Atx Breakout Board?
What benefits are there with buying an Atx Breakout Board?
What factors deserve consideration when shopping for an effective Atx Breakout Board?
Why is it crucial to invest in any Atx Breakout Board, much less the best one?
Which Atx Breakout Board are good in the current market?
Where can you find information like this about Atx Breakout Board?

We’re convinced that you likely have far more questions than just these regarding Atx Breakout Board, and the only real way to satisfy your need for knowledge is to get information from as many reputable online sources as you possibly can.

Potential sources can include buying guides for Atx Breakout Board, rating websites, word-of-mouth testimonials, online forums, and product reviews. Thorough and mindful research is crucial to making sure you get your hands on the best-possible Atx Breakout Board. Make sure that you are only using trustworthy and credible websites and sources.

We provide an Atx Breakout Board buying guide, and the information is totally objective and authentic. We employ both AI and big data in proofreading the collected information. How did we create this buying guide? We did it using a custom-created selection of algorithms that lets us manifest a top-10 list of the best available Atx Breakout Board currently available on the market.

This technology we use to assemble our list depends on a variety of factors, including but not limited to the following:

Brand Value: Every brand of Atx Breakout Board has a value all its own. Most brands offer some sort of unique selling proposition that’s supposed to bring something different to the table than their competitors.
Features: What bells and whistles matter for an Atx Breakout Board?
Specifications: How powerful they are can be measured.
Product Value: This simply is how much bang for the buck you get from your Atx Breakout Board.
Customer Ratings: Number ratings grade Atx Breakout Board objectively.
Customer Reviews: Closely related to ratings, these paragraphs give you first-hand and detailed information from real-world users about their Atx Breakout Board.
Product Quality: You don’t always get what you pay for with an Atx Breakout Board, sometimes less, and sometimes more.
Product Reliability: How sturdy and durable an Atx Breakout Board is should be an indication of how long it will work out for you.

We always remember that maintaining Atx Breakout Board information to stay current is a top priority, which is why we are constantly updating our websites. Learn more about us using online sources.

If you think that anything we present here regarding Atx Breakout Board is irrelevant, incorrect, misleading, or erroneous, then please let us know promptly! We’re here for you all the time. Contact us here. Or You can read more about us to see our vision.

FAQ:

Q: What kind of power supply does an ATX breakout board support?

A: ATX Power Supply Breakout Board and Acrylic Case Kit. with ADJ Adjustable Voltage Knob, Supports 3.3V, 5V, 12V and 1.5V-9.0V (ADJ) Output Voltage, 2A Maximum Output, Reset Protection. . . . Only 7 left in stock – order soon.

Q: What kind of voltage does a breakout board need?

A: In practice most power supplies use a 5.0V high-state voltage and can supply plenty of current, but just to be safe the breakout board buffers the PWR_OK line using a 5V 8mA push-pull buffer IC.

Q: What are the power rails on an ATX power supply?

A: The main three power rails are the +12V, +5V, and +3.3V rails. In addition, all ATX power supplies also provide a -12V rail and a +5V standby rail, and older power supplies provide a -5V rail.

Q: How does chain sync work on a ZSX breakout board?

A: Our Patent Pending Chain Sync Feature through our X6B, X7B, X11, and ZSX Breakout boards is done by connecting the interconnect cable from PSU 1 to PSU2, PSU 2 to PSU 3, and so on. Feature tested with up to 20 PSU in a Daisy Chain.